Routines

 

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

X

Y

Z

 

F
	find_freq_from_fid( )	get the CPU frequency
H
	halBoardInfoGet( )	retrieve the board info
	halBoardInfoShow( )	print the board info
	halDrvCtrlShow( )	show routine
	halInstConnect( )	third level initialization routine of timer device
	halInstInit( )	first level initialization routine
	halInstInit2( )	second level initialization routine of timer device
	halRegister( )	register hal driver
	halTopMemGet( )	get the top of the memory
I
	i8259Init( )	initialize the PIC
	i8259IntBoi( )	detect whether it is spurious interrupt or not
	i8259IntBoiEem( )	issue EOI before the IRQ0 interrupt handler
	i8259IntBoiSmm( )	enable Special Mask Mode before the IRQ0 interrupt handler
	i8259IntEoiMaster( )	send EOI(end of interrupt) signal to the master PIC.
	i8259IntEoiSlave( )	send EOI(end of interrupt) signal to the slave PIC.
	i8259IntEoiSlaveNfnm( )	send EOI(end of interrupt) signal to the slave PIC.
	i8259IntEoiSlaveSfnm( )	send EOI(end of interrupt) signal to the slave PIC.
	i8259IntEoiSmm( )	disable Special Mask Mode with EOI signal to the master PIC
M
	mc146818RtcInstConnect( )	third level initialization routine of the RTC
	mc146818RtcInstInit( )	first level initialization routine of the RTC
	mc146818RtcInstInit2( )	second level initialization routine of the RTC
	mc146818RtcTimeGet( )	retrieve the current date and time
	mc146818RtcTimeSet( )	Set the current date and time
S
	sysBspRev( )	return the BSP version and revision number
	sysBusIntAck( )	acknowledge a bus interrupt
	sysBusIntGen( )	generate a bus interrupt
	sysBusTas( )	test and set a location across the bus
	sysBusToLocalAdrs( )	convert a bus address to a local address
	sysDelay( )	allow recovery time for port accesses
	sysHwInit( )	initialize the system hardware
	sysHwInit2( )	additional system configuration and initialization
	sysIntDisablePIC( )	disable a bus interrupt level
	sysIntEnablePIC( )	enable a bus interrupt level
	sysIntEoiGet( )	get EOI/BOI function and its parameter
	sysIntInitPIC( )	initialize the interrupt controller
	sysIntLevel( )	get an IRQ(PIC) or INTIN(APIC) number in service
	sysIntLock( )	lock out all interrupts
	sysIntUnlock( )	unlock the PIC interrupts
	sysLocalToBusAdrs( )	convert a local address to a bus address
	sysMailboxConnect( )	connect a routine to the mailbox interrupt
	sysMailboxEnable( )	enable the mailbox interrupt
	sysMemTop( )	get the address of the top of VxWorks memory
	sysMmuMapAdd( )	insert a new MMU mapping
	sysModel( )	return the model name of the CPU board
	sysMsDelay( )	delay specified number of miliseconds
	sysNvRamGet( )	get the contents of non-volatile RAM
	sysNvRamSet( )	write to non-volatile RAM
	sysPciIvecToIrq( )	get an IRQ(PIC or IOAPIC) number from vector address
	sysPhysMemTop( )	get the address of the top of physical memory
	sysProcNumGet( )	get the processor number
	sysProcNumSet( )	set the processor number
	sysStrayInt( )	Do nothing for stray interrupts.
	sysToMonitor( )	transfer control to the ROM monitor
	sysUsDelay( )	delay specified number of microseconds
V
	vxbMc146818RtcDrvRegister( )	registers the driver for MC146818 RTC
	vxbusHalBoardInfoGet( )	method to retrieve the board info
	vxbW83627dhgDrvRegister( )	register template sensor driver
	vxbW83627wdtDrvRegister( )	register template driver
W
	W83627dhgFanGet( )	retrieve fan values
	W83627dhgInstConnect( )	third level initialization routine of sensor device
	W83627dhgInstInit( )	first level initialization routine of sensor device
	W83627dhgInstInit2( )	second level initialization routine of sensor device
	W83627dhgIODir( )	set GPIO direction
	W83627dhgIODirGet( )	retrieve GPIO direction settings
	W83627dhgIOEdgeDetectGet( )	Check edge event
	W83627dhgIOInvert( )	Set invertion for IO pins
	W83627dhgIOInvertGet( )	Get invertion for IO pins
	W83627dhgIOPins( )	set state of output IO pins
	W83627dhgIOPinsGet( )	retrieve state of IO pins
	W83627dhgIOTrigger( )	Update trigger & and input filter settings
	W83627dhgIOTriggerGet( )	Get trigger & and input filter settings
	W83627dhgSetFanSpeed( )	set fan speed value
	W83627dhgShow( )	show routine
	W83627dhgTempGet( )	retrieve the value of the current temperature
	W83627dhgTempGetMax( )	retrieve the maximum value of the temperature
	W83627dhgTempHyst( )	retrieve temperature sensor hysteresis values
	W83627dhgVoltageGet( )	retrieve voltage values
	W83627wdtInstConnect( )	third level initialization routine of device
	W83627wdtInstInit( )	first level initialization routine of device
	W83627wdtInstInit2( )	second level initialization routine of device
	W83627wdtWDTCount( )	Reload counter with new value
	W83627wdtWDTCountGet( )	Get current WDT value
	W83627wdtWDTDisable( )	Disable WDT module
	W83627wdtWDTEnable( )	Enable WDT module
	W83627wdtWDTMode( )	Set time unit for WDT